丰满熟妇无码久久精品国产,亚洲人成色777777精品音频 ,刺激视频哔哩哔哩,国产精品久久久久精品三级卜

Welcome [Wuxi Yi Jin Machinery Co. Ltd.] official website!
Chinese   |   English   |  Sitemap
News

Position:Home > News >

Centrifugal fan installation

Centrifugal fan in the end is how to install, centrifugal fan manufacturers of workers is described as follows:
1.Centrifugal fan of the overall unit installation, should be placed directly on the basis of pairs of oblique horn leveling.
2.On-site assembly of the centrifugal fan, the base of the cutting surface should be properly protected, there should be no corrosion or operation, the base placed on the basis of the application of pairs of oblique horn leveling.
3.The bearing seat and the base should be tightly engaged, the vertical non-level should not exceed 0.2 / 1000, with the level on the spindle measurement, horizontal horizontal water should not exceed 0.3 / 1000, with the level of the bearing in the level of the sub-surface measuring.
4.Before the bearing grinding, the rotor axis should be corrected with the axis of the chassis, and the gap between the impeller and the inlet and the clearance between the spindle and the rear side of the housing should be adjusted to match the equipment technology The provisions of the document.
5.When the spindle and the bearing are assembled, they should be inspected according to the equipment technical documents. Bearing bearing and bearing pad should be maintained between 0.03-0.04 mm interference.
6.When the fan housing is assembled, the position of the housing should be determined on the basis of the rotor axis and the axial and radial clearance between the inlet of the impeller and the air inlet of the cabinet should be high and within the specified range. Whether the anchor bolts are fastened. If the gap is not specified in the technical documentation, the general axial clearance shall be 1/100 of the outer diameter of the impeller. The radial clearance shall be evenly distributed. The value shall be 1.5 / 1000-3 / 1000 of the outer diameter of the impeller. Adjust the value of the gap to try to improve the efficiency of the fan.
7.When the fan is correct, the fan shaft and the motor shaft of different degrees of axis: radial displacement should not exceed 0.05 mm, the tilt should not exceed 0.2 / 1000.
8.Rolling bearing assembly of the centrifugal fan, the two bearing frame on the bearing hole of different shaft degrees, until the rotor is installed, to flexible rotation prevail.

Contact: Mr. Wei 180 6833 7327 / 133 9518 5578 7 ????Tel: 0510-83303276 ????Fax: 0510-83303276

E-mail: 2637472470@qq.com ????Web: www.91habit.com ????Add: Luoxian Town, Huishan District, Wuxi City

Copy right ? 2017 Wuxi Yi Jin Machinery Co., Ltd. All Rights Reserved

介休市| 五指山市| 晋宁县| 丹阳市| 衡东县| 桐乡市| 会昌县| 九龙县| 延边| 天全县| 昌乐县| 阳春市| 洪洞县| 仪陇县| 娱乐| 资兴市| 岢岚县| 锡林郭勒盟| 洛南县| 怀远县| 巨野县| 邵阳市| 乌兰浩特市| 乌兰察布市| 高平市| 砚山县| 宜阳县| 大竹县| 柳林县| 宁阳县| 思南县| 莎车县| 柳林县| 南陵县| 福清市| 柘城县| 抚州市| 清河县| 玛多县| 安泽县| 通化市|